Wireless Wifi Two-way Audio Pan/Tilt IP Network Camera + IR-CUT H6-186B White

Features

With IR-CUT and WPS functions
Simple and quick to setup, friendly user interface
Built-in microphone, users can intercom directly
Support for dynamic IP, with the only one global free domain name
Browser IE 6.0/7.0/8.0 Firefox
Allow remote viewing video and record from any internet connection
Supports two-way voice
Support two way audio monitoring
Multi-level users access and management with password protection load
Enable user monitoring by user's Smartphones(Android/apple's Iphone)
Can support 10 people online viewing at the same time

Specifications

TV System	NTSC
Image Compression Format	The standard M-JPEG
Image Resolution	VGA(640x480) / QVGA(320x240)
The Largest Image Transfer Rate	30/sec(QVGA), 30frames/second(VGA)
Sensors	1/4 CMOS Sensor
The Minimum Illumination	0.5Lux@550nm
Lens Type	Glass lens
Audio	Support two way audio monitoring
Ethernet	One 10/100Mbps RJ-45
Support protocol	HTTP,FTP,TCP/IP,UDP,SMTP,DHCP,PPPoE,DDNS,UPnP
Wireless Standard	IEEE 802.11b/g/n
Pan/Tilt Angle	Horizontal:270° & Veritcal:120°
Infrared Light	11 IR LEDs, night visibility up to 10 meters
Alarm Input	1 channel on/off input
Alarm Output	1 channel 5V replay output
Power Supply	DC5V/2A (US adapter)
Power Consumption	5 Watts(Max.)
Operate Temper	0℃~ 55℃(14℉~122℉)
Operate Humidity	20%~85% non-condensing
Storage Temper	-10℃~ 60℃(14℉~140℉)
Storage Humidity	0%~90% non-condensing
Color	White
Demension	(12.5 x 10.5 x 12.5)cm / 4.92" x 4.13" x 4.92" (L x W x H)

Package Includes

1 x IP camera(with WiFi antenna)
1 x CD-ROM
1 x Adapter
1 x Bracket
1 x Manual
1 x RJ45 Cable

Extra Info

NOTICE:

1. When Search Ip camera in LAN

a. Make sure the equipment is properly connected with thenetwork and power.
b.
The router must support DHCP (Dynamic Host ConfigurationProtocol), because dynamic IP addresses obtaining is one ofthe factory settings of camera. If the device cannot get thecorrect ip address, it will use the default ip address.
c.
The camera cannot be immediately used when power connectionis OK, system initialization will cost more than 20 seconds.

2. When the IP Camera Tool could not find camera′s IP address, please check if the camera works well. Check if network cable is loose or not. Make sure DHCP is enabled in your router, don′t enable MAC address filter.
Make sure that firewall or anti-virus software does not block the camera. You can add the camera as a trusted site in your firewall or anti-virus software.

3. ipcamtools.exe is only used to search for the LAN IPaddresses and port numbers of the cameras. However, the tool is notable to search IP address of the camera as well as the port numberin WAN.

4. The factory default settings using DHCP to obtain IP address.After restoring the factory settings, device IP address may bedifferent from the one before restoration. Please use the search toolto search for equipment. And obtain the corresponding IP.

5. more than one user can see the IP camera feed simultaneously, but due to the current IP camera chip computing power, it determines that the general IP camera supports up to 10 users. And the internet speed also limits the number of remote users. Particular depends on what the viewer stream, what kind of resolution and the traffic of the network broadband. If the speed is allowed (such as local area network) more than 10 simultaneous users want to view the camera, we can set up a proxy to achieve the purpose of watching at the same time.

6. DDNS: Dynamic DNS, also called as dynamic domain name, isused to handle the problem that user′s device doesn′t havefixed IP while accessing Internet. With assist of DDNS, usercan connect to his/her IP camera directly via DDNS. If user wants to access his/her IP camera via WAN, twoconditions, mentioned as follows, must be met.

OP Concepts